AutoCodes.com | All About OBDII Engine Codes
AutoCodes - GMC - P1153 GMC

P1153 GMC Code - HO2S Insufficient Switching Bank 2 Sensor 1

- Code Popularity: 40,475 Views
- Repair Importance Level: 3/3
- Repair Difficulty Level: 2/3
Table of contents
Share on Facebook   Share on Twitter   Share on Linkedin

What are the Possible Causes of the DTC P1153 GMC?

NOTE: The causes shown may not be a complete list of all potential problems, and it is possible that there may be other causes.
  • Faulty Heated Oxygen Sensor (HO2S) Bank 2 Sensor 1
  • Heated Oxygen Sensor Bank 2 Sensor 1 harness is open or shorted
  • Heated Oxygen Sensor Bank 2 Sensor 1 circuit poor electrical connection
  • Low or high fuel system pressure
  • Fuel contamination
  • Faulty fuel injectors
  • Exhaust gas leaks
  • Engine vacuum leaks
⚠ Does your GMC have Safety Recalls? → Check here

How to Fix the DTC P1153 GMC?

Review the 'Possible Causes' mentioned above and visually examine the corresponding wiring harness and connectors. Ensure to check for any damaged components and inspect the connector pins for signs of being broken, bent, pushed out, or corroded.

Code Tech Notes

Replacing the Front Heated Oxygen Sensors (HO2S) usually takes care of the problem

Search for P1153 GMC Questions and Answers: Search here →

What is the Cost to Diagnose the Code?

Labor: 1.0

To diagnose the P1153 GMC code, it typically requires 1.0 hour of labor. The specific diagnosis time and labor rates at auto repair shops can differ based on factors such as the location, make and model of the vehicle, and even the engine type. It is common for most auto repair shops to charge between $75 and $150 per hour.

What are Code Possible Symptoms?

  • Engine Light ON (or Service Engine Soon Warning Light)

Code P1153 GMC Description

The Heated Oxygen Sensors (HO2S) are used for fuel control and catalyst monitoring. Each HO2S compares the oxygen content of the surrounding air with the oxygen content of the exhaust stream. When the engine is started, the Engine Control Module (ECM) operates in an Open Loop mode, ignoring the HO2S signal voltage while calculating the air-to-fuel ratio. While the engine runs, the HO2S heats up and begins to generate a voltage within a range of 0 - 1, 000 mV. Once sufficient HO2S voltage fluctuation is observed by the ECM, Closed Loop is entered. The ECM uses the HO2S voltage to determine the air-to-fuel ratio. An HO2S voltage that increases toward 1, 000 mV indicates a rich fuel mixture. An HO2S voltage that decreases toward 0 mV indicates a lean fuel mixture.
The heating elements inside each HO2S heat the sensor to bring the sensor up to operating conditions faster. This allows the system to enter Closed Loop earlier and the ECM to calculate the air-to-fuel ratio sooner.
The Diagnostic Trouble Code (DTC) will be set when the ECM detects that the heated oxygen sensor rich-to-lean counts or the lean-to-rich counts are less than a calibrated value greater than 100s.
OBDII Code P1153 GMC - HO2S Insufficient Switching Bank 2 Sensor 1 - AutoCodes.com
P1153 GMC Code - HO2S Insufficient Switching Bank 2 Sensor 1

Need More Information on the Code?

Need more information on how to fix the P1153 GMC code? Get Access to Factory Service Manuals

Need Help with the Code?

Get the P1153 GMC code diagnosed by a professional: Find a repair shop in your area

Code P1153 GMC comments

Help us improve AutoCodes.com. Leave a comment below or tell us if the information above helps you fix the code. What are the symptoms on your vehicle for the P1153 GMC code? Have you replaced any parts?
Any information is appreciated. Thanks